Material Development

The 9-Point Check I Run Before Ordering Carbon, Basalt, or Viscose Fabric (Built From $14K of My Own Mistakes)

Who this is for

I handle material purchasing for a composites and technical-textile business. Since 2017 I've placed orders for carbon fabric, basalt fabric, waterproof laminates, and cellulose-based fibers — and in that stretch I've personally made six ordering mistakes that cost real money. Around $14,000 total, maybe $13,600, I'd have to pull the ledger. This checklist is what came out of the other end of that.

It's for buyers placing production or repeat orders. If you're ordering 50 meters as a one-off sample, some of this is overkill. If you're releasing a container order, none of it is. Nine points, in the order I actually use them.

1. Get the fiber designation and the lot datasheet — not the trade name

"Toray carbon fiber" is not a specification. Neither is "T700." T300, T700S, T800S, T1100G are different fibers with different published datasheet values, and the datasheet value for the raw fiber is not the value you'll see in your finished laminate. If a supplier quotes only a brand name or only a filament grade, ask for the grade plus the current production lot datasheet.

Same rule for basalt. "Basalt fiber fabric" covers everything from 6 µm chopped strand to 13 µm continuous woven roving. Those are not interchangeable products.

2. Ask for the sizing (finish) specification

This is the one almost everyone skips. I skipped it for two years. Sizing is the coupling agent applied to the fiber surface, typically 0.5–1.5% by weight, and it decides whether your resin actually bonds to the fiber. An epoxy-compatible sizing and a PA/PPS-compatible sizing are different products that happen to look identical on a roll.

If the datasheet says "epoxy sizing" and stops there, ask which epoxy system it was qualified against. That one question has saved us from at least two delamination problems we'd have found out about six months too late.

3. For basalt, get the oxide composition and the filament diameter

Continuous basalt fiber typically runs 9–13 µm in filament diameter, and published tensile strength lands somewhere in the 2,600–3,100 MPa band — which is a wide band. It depends on melt chemistry and drawing conditions. Ask for the Fe₂O₃ content if the part sees heat, and ask which diameter the quoted strength was measured at.

If the answer is "standard basalt," the answer is no.

4. For unidirectional carbon fabric, check areal weight and fiber volume separately

It's tempting to think two 300 gsm UD carbon fabrics from two suppliers are the same product. But that number is total areal weight — fiber plus resin film. The split between the two is where the difference hides, and a 200/100 fiber-to-resin split behaves very differently from a 240/60, even though both print "300 gsm" on the box.

Ask for: fiber areal weight, resin film weight, and fiber volume fraction of the cured laminate. If a unidirectional carbon fabric supplier gives you one number instead of three, ask again.

5. For waterproof fabric, get the membrane type AND the test method

"20,000 mm waterproof" means nothing without the method. ISO 811, AATCC 127, and JIS L 1092 will produce different numbers on the same piece of fabric. Ask which standard was used, and on which side of the fabric.

Then separate the three things buyers constantly lump together: a DWR (durable water repellent finish), a coating, and a membrane laminate. They fail in completely different ways. A DWR will wash out in 20–30 home launderings. A PU coating can hydrolyze in humid storage over a year. A PTFE or ePTFE membrane is a different cost bracket entirely.

If you're specifying a Toray waterproof fabric or any other branded waterproof textile, get the fabric-specific test certificate, not the brand family marketing sheet. Those two documents describe different things. (Note to self: I still need to file these by mill, not by brand.)

6. For viscose, ask for pulp origin, process route, and tenacity

"Viscose" covers at least three processes. Classic viscose uses carbon disulfide, and depending on the plant the CS2 recovery rate sits somewhere between 70% and 95%. Lyocell is solvent-spun with NMMO. Modal and high-wet-modulus are modified viscose variants. Different environmental profiles, different wet strength, different cost.

What I ask for now when qualifying a viscose fiber supplier: pulp origin (with FSC or PEFC chain-of-custody if your customer cares), the process route, dry and wet tenacity in cN/dtex, denier, and whether they will name the pulp mill. If they won't name the mill, assume it moves around between lots.

7. Get a sample from the actual production lot — not a "representative" sample

We learned this one the expensive way in September 2022. The supplier sent a beautiful 5-meter sample. The production lot came off a different line. GSM was about 8% off, the weave was visibly looser, and wet-out time in epoxy roughly doubled on the shop floor.

That order became a four-figure mistake plus a one-week production delay, and it's the reason point 7 exists. Request the sample pulled from the actual lot number you're being quoted, and put the lot number on the PO.

8. Put the tolerances and test methods in writing before you release the order

"±5%" on what, measured how, by whom? A tolerance without a method is just a future argument. Specify: which property, which standard (ASTM D3776 for areal weight, ASTM D3039 for composite tensile, ISO 2062 for yarn tensile), which lab, and what happens if the lot comes in out of spec.

Five minutes of this at the PO stage beats five days of it after the goods arrive.

9. Ask who actually made it

Not who's selling it. Most suppliers in this space are traders with a mill relationship. That's fine — until something goes wrong and you need to know who to call. Get the mill name and the mill's production lot number printed on the shipping documents, not just the invoice.

We ask now. It caused one awkward conversation and prevented three later ones.

Two things I'd add

Here's the thing: a fast quote is not a good quote. In Q1 2024 we ran the same written spec past four suppliers and got landed-cost quotes that spread about 38%. Same stated numbers on paper. The variance was in sizing, resin split, and freight terms — none of which were in the headline price.

And second: almost every failure I've documented was not a quality failure. It was a specification failure. The fiber was fine. My order was underspecified. That's the whole point of a checklist — it doesn't make you smarter, it just makes you slower in the places where being fast is expensive.

Errors I still see people make after the order ships

  • Ordering to a brand name instead of grade-plus-lot
  • Assuming the sample lot equals the production lot (see point 7, and my September 2022)
  • Accepting a waterproof figure without the test method
  • Treating "viscose" as a single product category
  • Never asking about sizing until the laminate fails

I'm not going to quote you a price for any of this — the category moves too much. I've watched quotes for identical basalt specifications move roughly 30% inside six months depending on freight and mill capacity. Get three quotes, but get them on the same written spec, or you're comparing nothing. (Based on quotes I collected in Q1 2025; verify current rates with your own suppliers.)

Beatriz Costa
Beatriz Costa

Beatriz Costa is an outdoor and performance-fabric analyst specializing in waterproof shells, breathable laminates, ripstop, nylon and polyester oxford, tent cloth, backpack fabrics, awnings, and solution-dyed textiles. She uses ISO 811 hydrostatic-pressure and ISO 13937-2 tear methods while tracking water resistance, tear force, moisture-vapour transmission, air permeability, coating adhesion, UV colourfastness, abrasion, and low-temperature flexibility. Her technical comparisons help outdoor brands, converters, and equipment manufacturers balance protection, breathability, durability, packability, seam construction, and climate exposure.